- 1 Where do you nail your tongue and groove?
- 2 How do you attach a tongue and groove board?
- 3 Do you glue tongue and groove paneling?
- 4 What kind of nails do you use for tongue and groove?
- 5 What is cheaper shiplap or tongue and groove?
- 6 What is better shiplap or tongue and groove?
- 7 Is tongue and groove cheaper than drywall?
- 8 How do you install tongue and groove vertically?
- 9 How much does tongue and groove ceiling cost?
- 10 Can I use tongue and groove in a bathroom?
- 11 How do you measure tongue and groove?
- 12 Can you use a brad nailer for paneling?
- 13 What’s the difference in a brad nailer and a finish nailer?
Where do you nail your tongue and groove?
Avoid visible nail holes
- Install planks with the tongue up.
- Nail at an angle directly through the tongue and into your studs. You don’t need to nail through the face of the planks anywhere but on the bottom row and near the ceiling.
- Start with the bottom row first and work your way up.
18 апр. 2014 г.
How do you attach a tongue and groove board?
Hang each board of the first and every successive row, always ensuring the board is the proper length or height before attaching. Butt edges together in the same row, and slide the groove of the next board over the previous tongue for each following row. Nail only the tongue side for each row after the first.
Do you glue tongue and groove paneling?
+1 on no glue in the T&G joint. The individual boards need to be able to expand contract individually (That’s the advantage of T&G). To solve the exposed unfinished tongue issue, you can pre-stain and finish the tongues before assembly.
What kind of nails do you use for tongue and groove?
We recommend using 16- or 18-gauge finish or brad nails. 1-½” to 2” in length should be sufficient. Both gauges are strong enough to hold the lumber securely, but small enough as to not leave a large hole on the face of the board. Go ahead and buy the bulk pack: you’re going to need it!
What is cheaper shiplap or tongue and groove?
Shiplap is cheaper than tongue and groove, but it requires a bit more work on the carpenter to get the rows to lay flat against the building in a waterproof fashion. Also, if not installed properly, shiplap is more likely to warp and leak than its counterpart.
What is better shiplap or tongue and groove?
Tongue and groove makes a stronger shed, which is harder to break into. Shiplap tongue and groove sheds share many of the same qualities as regular tongue and groove sheds, but the Shiplap has one special feature. Shiplap cladding has a little channel running along side the timber.
Is tongue and groove cheaper than drywall?
One of most frequently asked questions is: Isn’t tongue and groove more costly than drywall? Generally, yes–the retail cost of T&G will cost you more than drywall. But the labor is where the cost comes down considerably, with regard to modular cabins.
How do you install tongue and groove vertically?
To install tongue and groove paneling vertically, begin by nailing 1-by-3 furring strips horizontally either directly to the wall studs on a new wall or over the drywall on a finished wall. The paneling will be nailed directly to these furring strips.
How much does tongue and groove ceiling cost?
So, we know the tongue and groove ceiling looks awesome, but the big question is it affordable? According to the material you choose it can run anywhere from $2.00-$3.50 per square foot.
Can I use tongue and groove in a bathroom?
The most common use for both tongue and groove and shiplap is to panel entire walls, particularly in the kitchen or bathroom. But you can also use both styles to create just one accent wall, or even as a backsplash or fireplace surround.
How do you measure tongue and groove?
How do you measure tongue and groove flooring?
- Divide the floor area into rectangles.
- Measure the width and length of each rectangle.
- Multiple the width by the length for each rectangle to determine the surface area.
- Determine the area of an individual piece of tongue and groove flooring.
- Divide the total surface area by the area of a single piece of flooring.
Can you use a brad nailer for paneling?
Nail guns save an amazing amount of time on large projects. A brad nailer — also called a tacker or a stapler — is intended for precision work. … They are therefore well-suited to craft projects and for use in projects where the surface cannot be finished further, such as wall paneling.
What’s the difference in a brad nailer and a finish nailer?
The primary difference between a brad nailer vs a finish nailer is that the brad nail gun shoots 18-gauge nails whereas 16-gauge or 15-gauge nails are used in the finish nailer. … With a brad nailer, you can attach thin trims and moldings without the need for using putty.