Start with two pieces of baseboard that have 90-degree cuts at opposite ends. To create the scarf joint in the middle, place the first board in place and mark a 45-degree cut at a stud location. Using the miter saw, cut this end of the first board at a 45-degree angle and sand it smooth. Don’t oversand.
- 1 Should I glue or nail baseboards?
- 2 What is the best way to attach baseboard molding?
- 3 Where do you nail baseboards?
- 4 Do you need to nail baseboards into studs?
- 5 What size nails should you use for baseboards?
- 6 What type of baseboards are in style?
- 7 Are baseboards worth replacing?
- 8 Do you install baseboards before or after flooring?
- 9 Can I use a brad nailer for baseboards?
- 10 What kind of nail gun do I need for trim?
Should I glue or nail baseboards?
There’s no need to nail or glue them into place; just install the baseboard right over them, tight against the floor molding. It’s best to keep the nails at the bottom of the base above the gap so they go through drywall, not air.
What is the best way to attach baseboard molding?
You will need a few other tools and supplies to install baseboards. The handiest tool is a miter saw. A miter saw will help you quickly and accurately cut trim.
- Install shoe or cap moulding, if using. …
- Caulk along the top edge and corner edges and nail holes.
- Touch up the baseboard with primer paint.
Where do you nail baseboards?
Nail Baseboard to Wall
Set the scribed baseboard in place. Next, at each stud location, hammer two 8d finish nails through the board, at a slight downward angle, near its top and bottom edges. To avoid marking the wood, use a nail set to drive the heads just below the wood surface.
Do you need to nail baseboards into studs?
The general rule is to insert nails into the studs when another type of framing is not available. For example, chair rail molding, a decorative horizontal strip of trim that extends from wall to wall, requires nailing to the studs to hold it in place.
What size nails should you use for baseboards?
What size nail should I use for baseboards? As we discussed earlier with nail guns – the best baseboard nails are probably going to be 6d (2») or 8d (2.5» for baseboard). These can easily accommodate 15 gauge or 16 gauge nails, giving you a long, durable nail for thick baseboards and studs.
What type of baseboards are in style?
Baseboard Styles and Profiles
- Flat Baseboard Molding. This traditional baseboard is the simplest baseboard style you can get. …
- Jointed Baseboard Style. …
- Carved Baseboard for Upgrade. …
- High Trim Profile. …
- Clamshell Baseboard. …
- Ornate Baseboard. …
- MDF Baseboard. …
- Pinewood Baseboard.
Are baseboards worth replacing?
Designed to hide the seam where wall meets floor, baseboards give any room a finished look. If your trim is showing wear and tear, painting is always an option, but the prep work is important and can be time-intensive. Replacement is your best option if they’re water-damaged, stained or warped.
Do you install baseboards before or after flooring?
Baseboards are often installed before flooring, since they must be finished in place with either stain or paint and this is much easier without worrying about staining the hardwood, tile or carpet.
Can I use a brad nailer for baseboards?
Q. Can you use a brad nailer for baseboards? Brad nailers are suitable for baseboards. Most fire brads as long as 2 inches, which is enough to penetrate a 3/4-inch thick molding, 1/2-inch thick drywall, and bite into the framing lumber in the baseplate or wall studs.
What kind of nail gun do I need for trim?
16-gauge nails are the most versatile size, so a 16-gauge nail gun is a great option if you need it for many different projects. 15-gauge nails are most often used for installing thick trim. 18-gauge and higher-gauge nail guns are best used for fine detail work, furniture repair and thin trim work.