How do I exit config t?

To exit interface configuration mode and to return to global configuration mode, enter the exit command. To exit interface configuration mode and to return to privileged EXEC mode, enter the end command, or press Ctrl-Z.

What is the shortcut key for exit configuration mode?

Cisco IOS CLI Shortcuts

Shortcut Description
Ctrl+R Refresh
Tab Command autocomplete
Ctrl+C Exit. Exit from config mode
Ctrl+Z Apply the command line and exit from config mode ie. return to privileged EXEC mode.

What does Ctrl-Z do in Cisco?

Ctrl-Z: When in a config mode, ends the config mode and returns you to privileged EXEC mode. When in user or privileged EXEC mode, logs you out of the router.

What happens when the exit command is entered in privileged EXEC mode?

If you press exit in privileged EXEC mode what happens? The session ends. … To move from any submode of the global configuration mode to another «immediate» submode of the global configuration mode, simply enter the corresponding command that is normally entered from global configuration mode.

Read more  How do you find a song you can t find?

How do I check router configuration commands?

Basic Cisco Router Show Commands

  1. Router#show interfaces. This command shows the status and configuration of interfaces. …
  2. Router#show controllers [type slot_# port_#] …
  3. Router#show flash. …
  4. Router#show version. …
  5. Router#show startup-config.

6 авг. 2018 г.

What is user EXEC mode in Cisco?

User EXEC level allows you to access only basic monitoring commands; privileged EXEC level allows you to access all router commands. … There are five command modes: global configuration mode, interface configuration mode, subinterface configuration mode, router configuration mode, and line configuration mode.

Which command or key combination allows a user?

Which command or key combination allows a user to return to the previous level in the command hierarchy? Explanation: End and CTRL-Z return the user to the privileged EXEC mode. Ctrl-C ends a command in process. The exit command returns the user to the previous level.

What is Ctrl Break?

Filters. In a PC, holding down the Ctrl key and pressing the Break key cancels the running program or batch file. See Ctrl-C. 0.

What is copy running-config startup config?

Enter the copy running-config startup-config command to save the current running configuration to the startup configuration file in NVRAM. To display the startup configuration, enter the show startup-config command.

What is the Cisco break command?

A break signal enables you to access a ROM Monitor on Cisco IOS® devices when a password recovery is necessary.

What is the difference between user mode and privileged mode?

Privileged mode mode allows users to view the system configuration, restart the system, and enter router configuration mode. Privileged mode also allows all the commands that are available in user mode. … From the user mode, a user can change to Privileged mode, by running the «enable» command.

Read more  Does Best Buy do TV mounting?

How do I enter config mode?

To enter global configuration mode, enter the configure command. Global configuration From privileged EXEC mode, enter the configure command. To exit to privileged EXEC mode, enter the exit or end command, or press Ctrl-Z. To enter interface configuration mode, enter the interface configuration command.

What is privileged mode?

Supervisor mode or privileged mode is a computer system mode in which all instructions such as privileged instructions can be performed by the processor. Some of these privileged instructions are interrupt instructions, input output management etc.

What is config t command?

In privileged mode, you can show anything but not make changes. Next, type config terminal (or config t) to go to global configuration mode (where the prompt looks like router(config)# ). … Also from the global configuration mode, you can go into router configuration using the router {protocol} command.

What are the steps to configure a switch?

How to configure Cisco switch?

  1. Step 1: Use an external emulator such as Telnet or a PuTTY to login to the switch.
  2. Switch# configure terminal. …
  3. Step 2: Provide a hostname for the switch to function in a particular network environment.
  4. Switch(config)#hostname switch. …
  5. Step 3: Configure an administration password (enable secret password)

How do I access my router from command line?

Access router command line interface using Windows laptop

  1. Under Category, choose Session.
  2. Under Connection type, choose Serial.
  3. In the Serial line, enter the COM port on your laptop that is connected to the console port on your router, using the console cable.
  4. Click Open.
Read more  Can you use any TV remote on any TV?

14 авг. 2016 г.